IZOZENĀ® FLEXPRO TILE GROUT 2-5
IZOZENĀ® FLEXPRO TILE GROUT 2-5 is a cementbased, colored tile grout offering high mechanical strength and excellent color stability. Suitable for joint width 2-5 mm. Classified as type CG2 WA tile grout according to EN 13888.
ā¢ Non-shrink and prevent cracks
ā¢ Non-Sag / slump (thixotropic) application
ā¢ Consistent colour quality
ā¢ Easy to use and apply, just add water
Suitable for use in hot and tropical climatic conditions.
Fields of application
IZOZENĀ® FLEXPRO TILE GROUT 2-5 is used for grouting tile joints on walls or floors, for indoor and outdoor applications.
Technical data
Form: Cementitious Powder
Colors: See Color Chart
Water demand: 24ā26%
Bulk density of dry mortar: 1.40 Ā± 0.40 kg/l
Bulk density of fresh mortar: 1.90 Ā± 0.50 kg/l
Application temperature: from +5Ā°C to +35Ā°C
Pot life: at least 4 h at +20Ā°C
Walkability / Ready for foot traffic: after 24 hours
Flexural strength after 28 days: 6.00 N/mmĀ²
Compressive strength after 28 days: 40.00 N/mmĀ²
Abrasion resistance (EN 12808-2): ā¤ 1,000 mmĀ³
Water absorption (EN 12808-5):
30 min: ā¤ 2 g
240 min: ā¤ 5 g
Drying shrinkage (EN 12808-4): ā¤ 2 mm/m
Freeze-thaw resistance (25 cycles, EN 12808-3): 5.00 N/mmĀ²
Directions for Use
1. Substrate
The substrate covered with tiles should be perfectly clean. The joints should be carefully cleaned and dampened with a wet sponge.2. Application
IZOZENĀ® FLEXPRO TILE GROUT 2-5 is added to water under continuous stirring, until a homogeneous paste is formed. A low-speed mixer is recommended for the mixing. The mixture should be left to stand for about 3 min and then slightly stirred again. Spread the grout diagonally across the joints using a rubber float, making sure to fill them completely. The excess material should be wiped after a while, using a wet sponge, to avoid any change in color. Finally, the surface may be cleaned with a dry cloth. For use outdoors or at high temperatures, repeated dampening is recommended after a few hours and when the grout has dried.Consumption
The consumption depends on tile dimensions and joint width. Indicative values (in g/mĀ²):
| Tile Dimensions (cm) | Joint Width 2 mm | Joint Width 3 mm | Joint Width 4 mm | Ā |
|---|---|---|---|---|
| 2 Ć 2 Ć 0.3 | 1.3ā1.5 | ā | ā | Ā |
| 10 Ć 10 Ć 0.6 | 400ā600 | 800 | 1 | Ā |
| 15 Ć 15 Ć 0.7 | 310ā470 | 630 | 780 | Ā |
| 20 Ć 20 Ć 0.7 | 240ā360 | 480 | 590 | Ā |
| 20 Ć 30 Ć 0.7 | 200ā300 | 400 | 490 | Ā |
| 30 Ć 30 Ć 0.8 | 190ā280 | 370 | 460 | Ā |